HONDA HDS FOR 2007 MANUAL
HONDA HDS FOR 2007 REGISTRATION
HONDA HDS FOR 2007 CODE

HONDA HDS FOR 2007 REGISTRATION

The registration of keys has been completed.Honda wants ProFirst shops to use its i-HDS software to perform pre- and post-repair scans of customer vehicles. It prompt that вЂњIs the immobilizer indicator light turned off?вЂќ Turn the ignition switch to on within 20 seconds, without changing the key Turn the ignition switch off within 16 seconds

HONDA HDS FOR 2007 CODE

Personally, if the problem can be solved by paying a little,you would better to, it will save you much time.Д«ut sometimes, your customers unwilling to spend extra money or you got the incorrect PIN code by VIN, so you need to try other methods.ДЄfter input the PCM code, it prompt you to enter the key number you want to register. It will cost you $20~100 depend on your vehicle models, the accuracy rate is more than 95%.The advantage is that you do not need to disassemble any parts on the vehicle.After getting the PIN code, you are available to program keys directly. Inquire PIN Code by Dealer or Three-part via VIN.Д«ecause the VIN(Vehicle Identify Number) of each car is unique identification. If you they are different,the immo system VIN is more reliable.Дў.Make sure vehicle models is corresponding to the immo system.(many freshman select incorrect models)ДЈ.Immo system have been locked due to much time incorrect pin code enter(wait for hours or next day,try it again!) In summary, when you get incorrect PIN code by VIN calculating:ДЎ.Check difference between the appearance VIN and immo system VIN. Try to disassemble chip to read out pin code when you find the device can not support. Many devices can calculate the pin code by their programmer,you just need to plug the programmer into OBD socket to get pin code,then programming keys. Read out PIN code by auto key programmer:

The pin code is stored in the chip located in ECU,immo box,smart box or BCM box,it depend on the vehicle models.You need to remove chip from PCB,then use programmer to read out the pin code,the accuracy up to 99%.This method require you have skillful operations:disassembling,welding,reading out pin code. This vehicleвЂ™s VIN will be required to obtain the passwordвЂќДЎ.Inquire dealer to get immo pin code via VINДў.Disassemble immo box or smart box to read out the pin code by programmerДЈ.Read out immo pin code by auto key programmer

It prompt вЂњObtain PCM-code(IMMOBILIZER PCM CODE) for In This function does the necessary registration for registering new keys or deleting registered keys Then Exit the selection and select вЂњAdd and Delete KeysвЂќ Select вЂњSystem Check, Number of Keys and Status Log вЂќГ вЂќ Number Of KeysвЂќ Then you will see there are 5 options as below picture:Д«efore programming new keys, you would better to check the number of key. Please wait.ДЇor vehicle equipped with keyless Access System, use the actual immobilizer key in the remote to register and diagnose the system The keys can only be programmed with the ILCO key duplicator.Дetermining immobilizer system type.

The tester cannot program keys with T5 stamped on the blade of the key or with the word ILCO on the plastic head. Keep ignition ON until the tester directs you to turn the ignition off.

HONDA HDS FOR 2007 MANUAL

Refer to the Service Manual for further information Note: Not all system may be available on this vehicle. Run the Honda HDS software and enter вЂњSystem Selection MenuвЂќ Here is the test report: HIM HDS working for Accord 2007 all keys lostД¬onnect Honda HIM interface to your vehicle by OBD. You can make new keys to Accord with HDS if you have a decent HIM diagnostic tool. Possible to use Honda HDSВ to program new keys?

Honda hds for 2007